Friday, 9 November 2012

Compact Fluorescent Lamps - Advantages & Disadvantages


 Advantages

Compact fluorescents offer following advantages over incandescent light bulbs:
  • Lower power consumption i.e. CFL consumes 1/4 the energy, and produce 90% less heat as compared to incandescent lamps.
  • Longer lifetime (last up to 10 times longer than incandescent lights)
  • Produce more light

Disadvantages

  • Longer starts
  • More expensive than incandescent lamps owing to their higher initial cost.
  • CFLs are physically larger than incandescent lamps which may make them difficult to use in some light fixtures.
  • Fluorescent tubes contain a microscopic amount of mercury. It is such a small amount that disposal is not generally regulated as with full size fluorescents. Hence we should use caution to avoid crushing the tubes, and dispose of them safely. 

Thursday, 8 November 2012

Compact fluorescent lamp

Compact fluorescent lamps are smaller versions of standard fluorescent lamps. They consume between 5 to 27 watts, and have a brightness and color interpretation that is equivalent to incandescent lights. Unlike standard fluorescents, they can directly replace standard incandescent bulbs. Compact fluorescent lamps (CFLs) combine the energy efficiency of fluorescent lighting with the convenience and popularity of incandescent fixtures.

Working of CFL

Compact fluorescent lamps work to a great extent like standard fluorescent lamps. They consist of two parts:
  1. A gas-filled tube
  2. Magnetic or Electronic ballast
The gas in the tube glows with ultraviolet light when electricity from the ballast flows through it. This in turn excites a white phosphor coating on the inside of the tube, which emits visible light throughout the surface of the tube. Compact fluorescent lamps with magnetic ballasts flicker slightly when they start. Besides, they are heavier than electronic ballasts. Electronic ballasts are more expensive than magnetic ballasts. However, they are more efficient especially at low temperatures. Most currently available CFLs have electronic ballasts.

Compact Fluorescent Lamp Main Features

by Chipkin Automation Systems

Tuesday, 6 November 2012

Halogen Cycle


Halogen lamp is filled with the same inert gases as incandescent lamps mixed with small amounts of a halogen gas (generally less than 1% bromine). The halogen chemically reacts with the tungsten deposit to produce tungsten halides. When the tungsten halide reaches the filament, the intense heat of the filament causes the halide to break down, releasing tungsten back to the filament. This process is known as the tungsten-halogen cycle and it maintains a constant light output over the life of the lamp. To make this halogen cycle to work following are the basic requirements:
  • The bulb surface must be very hot otherwise the halogen may not effectively vaporize or fail to adequately react with condensed tungsten.
  • The bulb needs to be smaller and made of either quartz or a high-strength, heat-resistant grade of glass known as aluminosilicate.
Since the bulb is small and reasonably strong due to its thicker walls, it can be filled with gas to a higher than normal pressure. This slows down the evaporation of the tungsten from the filament, increasing the life of the lamp. The higher pressure and better fill gases can extend the life of the bulb and permit a higher filament temperature which results in better efficiency.

Wednesday, 24 October 2012

Arc Lamp

It is a type of electric-discharge lamp in which an electric current flows between electrodes through a gas or vapor. In nearly every arc lamp, the light results from the luminescence of the gas. However in carbon arc lamp, the light is produced by the incandescence of one or both electrodes. The color of the arc depends upon the electrode material and the surrounding atmosphere. Majority of the lamps have a negative resistance characteristic so that the resistance decreases after the arc has been struck. Consequently some form of current-limiting device is required in the electric circuit. Arc Lamp Features.

Bacnet Protocol Converters

Tuesday, 23 October 2012

Ballast Factor (BF)

It is the measured ability of particular ballast to produce light from the lamps it powers. It is derived by dividing the lumen output of a particular lamp/ballast combination by the lumen output of the same lamps on reference ballast. Hence, Ballast factor is the ratio of the luminous output of a lamp when operated on ballast to its luminous output when operated under standardized rating conditions. In other words, it is the percentage of rated lumens from the same lamp using commercial ballast as compared to ANSI reference ballast. Ballast factor is not a measure of energy efficiency. For example, a ballast factor of .96 means the commercial ballast produces 96% of light produced by ANSI reference ballast operating the same lamp. The ballast factor can be referred to in the catalogs from fluorescent or HID ballast manufacturers.

Electronic Ballast

Thursday, 11 October 2012

Fluorescent lighting


Fluorescent lighting is a popular and efficient lighting system used globally. It is most commonly found in commercial facilities. Fluorescent lamps emit extremely bright glow without getting blistering hot like an ordinary light bulb. They are more efficient as compared to incandescent lamps. Fluorescent lamps and fixtures are certainly more expensive to install than incandescent lighting, but they are significantly cheaper to operate. Besides, the lamps last far longer than incandescent lamps, making the long term cost-of-operation for fluorescent lighting far less than incandescent lighting. Because of their versatility, fluorescent lamps are available in numerous sizes, types, shapes, colors and light intensity. Some are designed to operate in cold locations, while others generate large amounts of light at the expense of service life.
All fluorescent lamps grow dimmer with age, and they may even begin to flicker or flash on and off. These are warning signals, and we should make the necessary repairs as soon as we notice any change in the lamp's normal performance. A dim tube frequently requires replacement, and failure to replace it can strain other parts of the fixture. Also, repeated flickering or flashing will wear out the starter, causing the insulation at the starter to deteriorate.

Basic Concepts

Monday, 1 October 2012

Blackbody


A black body is a theoretical object that absorbs 100% of the radiation that strikes it. Consequently it reflects no radiation and appears perfectly black. However, in practice no material has been found to absorb all incoming radiation, other than carbon in its graphite form since it absorbs all but about 3%.
Black body is also an ideal emitter of radiation. At a particular temperature it would emit the maximum amount of energy possible for that temperature. This value is referred to as the black body radiation. The maximum wavelength emitted by a black body radiator is infinite. It also emits a definite amount of energy at each wavelength for a particular temperature, hence standard black body radiation curves can be drawn for each temperature, showing the energy radiated at each wavelength. All objects emit radiation above absolute zero.

Blackbody Example